This automated optical fiber tensile testing system is ideal for operator skill independent use in creation and lab settings. Two fundamental model configurations enable the user to choose between a set up for optical fiber ribbon machine with additional mandrels for rotary high strength testing.
The linear edition is designed for creation proof screening with causes as much as 22 N. Motorized clamps with carefully designed rubberized inserts ensure that the fiber covering is not really damaged inside the screening process while at the same time eliminating the necessity for an outside air supply. Amounts of tugging force, tugging speed and hold time are programmable and conveniently accessible to the owner with the built-in Liquid crystal display touch screen manage. Data from tests can be stored and reached via the Universal serial bus port or Ethernet interface.
Mandrels of the same design like NYFORS? optical fiber recoaters can be easily mounted on the proof tester inside the rotary higher power settings. The fiber is covered round the two mandrels which assistance it using a unique clamping mechanism. In this way higher lots can be employed to the fiber, allowing breaking up power tests under controlled conditions.
Adjustable clamp placement facilitates screening using the greatest force amounts as well as screening of short fiber measures. The lightweight and light weight style definitely makes the tool easy to move around inside a laboratory environment and also to incorporate within a production work bench where space is at reduced. The machine is a compact and light-weight instrument suitable for testing the effectiveness of optical fibers as much as 30 N. The machine is developed to meet all kinds of programs where a strength check must be performed.
The machine was created using the consumer in mind. The optical fiber ribbon machine is readily positioned in the carefully guided linear clamps, and the screening starts automatically using a One Contact go button. The built-in microprocessor regulates all of the essential parameters such as pulling force, tugging velocity and hold time. This allows to get a completely controlled test each and every time.
The machine can be linked to an outside PC, which enables use of all automated parameters and settings. The machine is adapted to stand-on your own use or even to the integration into various subsystems. The machine comes with an substantial capability of logging and saving information such as tugging force, pulling speed and fiber size as well as other parameters.
Two recoat injector designs can be found. The PTR307 uses a computerized pump to inject the recoat material. The quantity of material dispensed through the automatic injector is managed by hand via the top-installed “Inject” button or programmed into the machine using the tablet pc control. The PTR307B includes a manual recoat injection system that will require the consumer to manually dispense the recoat materials into the mold cavity; a replacement injector for your PTR307B recoater is accessible below. Please note that the automated injector is simply suitable for higher-index recoat materials, as the Fiber coloring machine works with each reduced- and high- directory bpabim materials; both are sold individually listed below. Make sure you get in touch with Technology Assistance for additional information.
he handbook injector can be mounted to compatible fiber recoaters using the 4-40 anchoring screws in the recoater housing (see picture to the right). Utilize a 3/32″ hex key to safe the injector before use. For connecting the PTRRRM for the recoater mold, tighten the connector after the eco-friendly plastic tubes, then release by way of a 1/4 turn to permit rotation.
The injector is equipped with a syndication device as well as 2-place selection lever for directing the stream of recoat material. A knurled dispensing attach with the internal plunger acts as a syringe for your recoat material. To fill the syringe, point the handle downward (i.e., towards the recoat bottle), then rotate the knurled dispensing attach counterclockwise till it rotates easily to fill the syringe (demonstrated in the photo towards the right). Then, to inject the recoat material to the mold, point the handle horizontally (i.e., facing the knurled attach) and rotate the attach clockwise until nearby the end from the travel range is reached. Steer clear of bottoming the dispenser since this may damage the interior plunger; also be careful when re-engaging the threads to prevent go across threading the dispensing screw. Several fill up/inject actions may be required until air is displaced within the system. Use camera lens cells as well as an acetone or alcohol cleaning solution to gather any extra recoat material that runs through the mold.