This automatic optical fiber tensile testing system is designed for operator skill impartial use within production and lab settings. Two fundamental model configurations enable the consumer to choose between a set up for regular linear proof screening with extra mandrels for rotary higher strength screening.

The linear edition is designed for production proof screening with forces as much as 22 N. Motorized clamps with very carefully developed rubber inserts be sure that the TCC Laser Printer For Cable is not damaged inside the testing process whilst concurrently eliminating the need for another air provide. Amounts of pulling force, tugging velocity and hold time are automated and conveniently available to the owner with the built in LCD touchscreen display manage. Data from assessments could be saved and reached using the USB port or Ethernet interface.

Mandrels of the same design as with NYFORS’ optical fiber recoaters can easily be mounted on the proof tester inside the rotary high power configuration. The fiber is wrapped across the two mandrels which support it having a special clamping mechanism. By doing this much higher lots does apply onto the fiber, enabling breaking strength tests under managed conditions.

Changeable clamp positioning facilitates screening with the greatest pressure amounts as well as screening of short fiber measures. The lightweight and lightweight weight design helps make the tool simple to maneuver within a laboratory environment and to incorporate inside a production work table where space is at a premium. The equipment is actually a compact and lightweight tool ideal for testing the effectiveness of optical fibers up to 30 N. The equipment is developed to meet all kinds of programs in which a strength check needs to be carried out.

The machine was created using the user in your mind. The Secondary Coating Line is definitely placed in the carefully guided linear clamps, as well as the screening begins instantly having a “One Touch” go button. The built in microprocessor controls all of the important guidelines such as pulling pressure, pulling speed and keep time. This permits to get a completely controlled test each and every time.

The device may be connected to an outside PC, which allows access to all programmable parameters and configurations. The equipment is tailored to stand-alone use or the incorporation into various subsystems. The equipment has an substantial capability of signing and saving details including tugging pressure, pulling speed and fiber size along with other parameters.

Two recoat injector designs are available. The PTR307 uses an automated pump to inject the recoat material. The quantity of material dispensed through the automatic injector is controlled by hand using the top-installed “Inject” switch or programmed into the device utilizing the tablet control. The PTR307B includes a handbook recoat shot system that requires an individual to personally dispense the recoat material to the mildew cavity; a replacement injector for that PTR307B recoater is accessible listed below. Take note that the automated injector is just compatible with high-directory recoat material, while the manual injector works with each low- and- index recoat materials; both of them are marketed individually below. Make sure you contact Tech Assistance for more information.

he manual injector could be installed to Cable Air Wiper using the 4-40 screws in the recoater housing (see photo off to the right). Use a 3/32″ hex factor to secure the injector before use. For connecting the PTRRRM to the recoater mildew, tighten up the connector at the end of the green plastic tubes, then release by way of a 1/4 consider enable rotation.

The injector is equipped with a syndication valve and 2-place selection handle for directing the flow of recoat materials. A knurled dispensing attach with an internal plunger works as a syringe for the recoat materials. To fill the syringe, point the handle downwards (i.e., toward the recoat bottle), then spin the knurled dispensing attach counterclockwise till it ikrsve freely to fill the syringe (demonstrated inside the picture off to the right). Then, to inject the recoat material in to the mildew, stage the handle horizontally (i.e., dealing with the knurled attach) and rotate the screw clockwise till near the end of the travel array is achieved. Steer clear of bottoming out the dispenser as this may harm the internal plunger; also be careful when re-interesting the threads to avoid cross threading the dispensing attach. Several fill up/inject steps may be needed till atmosphere is displaced inside the system. Use lens cells as well as an acetone or alcohol cleansing answer to gather any extra recoat material that flows from the mold.

Fiber Coloring Machine – Discover Innovative Insights..